Step-By-Step Instructions on How to Do Tape Transfers To Your PC
Generally, today’s tape players cannot stand in for one of the original tape players which Radio Shack sold with their computers. The lack of “EAR” output means that you are going to get a heavily processed signal out of a modern day tape player, and that processing will make it all but impossible to access TRS-80 data. Your only choice used to be to buy one of these old players, but Amardeep Chana has figured out that the EZCap Super USB Cassette Capture (about $20 on Amazon) works just fine (and has auto-reverse in case you want to “set it and forget it” for a whole tape).
Make sure your volume is set right.
With regard to the volume, first listen to the tape and see if it sounds right. If you have a treble control, you probably want maximum treble. Once it sounds good, then you can move on to trying to read it.
The next step depends on whether you are using a good old original Radio Shack computer tape player or the EZCap.
Original Tape Recorder (or anything using a LINE OUT)
Hook up a patch cable. Put one end in your the earphones jack on the tape recorder …
… and one end in your sound card’s line-in jack. Make sure to specify the input line (microphone or line in) on your recording software.
Go to FILE -> NEW and set the DEVICES settings to Channels: MONO and Input: Line In, and set the QUALITY settings to 48000 and 16 Bit
EZCap (or anything using USB)
Plug your EZCap USB cable into your computer’s USB port and wait for the operating system to recognize the device.
Not a necessary step, but one I recommend – Plug a set of earphones into the speaker port of the EZCap. This way you can hear if there is data or not.
Go to FILE -> NEW and set the DEVICES settings to Channels: MONO and Input: Microphone Array (USB PnP Audio), and set the QUALITY settings to 48000 and 16 Bit
Insert the cassette in your cassette recorder.
Press the RECORD button on Audacity
Then press PLAY on the cassette recorder.
(This is not a step – this is just what a CLOAD Magazine tape looks like as it records).
The volume setting of CLOAD cassettes is volume 5 on a CTR-80.
When done, presss the STOP button on Audacity, and the STOP button on the cassette recorder.
Click at the beginning of where you want to select and drag to the end of where you want to select (shown with light blue background). Leave a little spare space before and after.
Choose FILE -> EXPORT -> EXPORT SELECTED AUDIO.
File Name: (see below)
Save as Type: WAVE (*.WAV)
Attributes: PCM Unsigned, 8 bit, mono
In this example, I saved it as “FILE1” (no quotes) because its the first of many files.
Give it a name and select WAV and Unsigned 8 Bit PCM. Click OK. In this example, I chose NEWDUMP as the filename.
At this point you have saved the WAV file, and if you are using an emulator that can load WAV files, you can try to load the WAV there. The next steps are to convert it to a CAS file.
The Windows / WAV2CAS Way
In a DOS window where you saved the file from STEP 10, run WAV2CAS
followed by the filename of the file you just saved.
For my example, I typed “WAV2CAS FILE1” (no quotes) on the DOS Command Line, since I had called it “FILE1” (no quotes) in the above step.Click OK on the window which pops up.
A CAS file has now been created.
Make sure the STATUS flag says “OK” for the file you want to save as a CAS file. If not, you need to fix the volume and try again!
If it says OK, then click SAVE and choose which file (or files, you can choose multiple files) you want saved as a CAS file and then click SAVE again.
Enter a filename. For this example, I gave it the name firstfile.cas
All OS’s / Web Way
Using your computer’s file explorer, drag your WAV file into the main window. Once you do, the screen should switch to something like this ….
Click the .CAS button and save your file. If you want to test the file at this step, you can also hit any of the emulator buttons to the left.
At this point you have saved the WAV file into a CAS file. The rest is on how to load the CAS file into an emulator.
Run your TRS-80 emulator
. I am using TRS80GP which works off of a command line. Here I am telling the emulator to start in MODEL I mode, non-DOS, turbo speed, and mount the file firstfile.cas as a cassette.
Load your program (CLOAD for a BASIC file, and SYSTEM followed by the program filename) I then entered the CLOAD command to commence loading of the cassette image. You can see it is loading, by the “*” in the corner. If you are not getting “**” and “*” alternatively at a decent pace, your image is no good.
Possible solutions for the NO BLINK situation are to fix your volume level, or to make sure you are not CLOADing a SYSTEM tape.
LIST your program to make sure it looks ok, and enjoy.